McqMate
These multiple-choice questions (MCQs) are designed to enhance your knowledge and understanding in the following areas: Manufacturing Engineering .
Chapters
| 1. |
In welding symbol, if the symbol is above the baseline then the welding is to be done at |
| A. | The arrow side |
| B. | Other side of the arrow |
| C. | Right side of the arrow |
| D. | Both side of the arrow |
| Answer» B. Other side of the arrow | |
| 2. |
Where the welding symbol is placed when the welding is to be done at the arrow side |
| A. | Below the baseline |
| B. | Above the baseline |
| C. | A & B both |
| D. | None of them |
| Answer» A. Below the baseline | |
| 3. |
For the vertical position of the weld fillet and other symbols should saw in which side |
| A. | Right |
| B. | Left |
| C. | Bottom |
| D. | Above |
| Answer» B. Left | |
| 4. |
The full form of DFW is |
| A. | Direct finish weld |
| B. | Direct fusion welding |
| C. | Diffusion welding |
| D. | Double fusion Welding |
| Answer» C. Diffusion welding | |
| 5. |
Full form of FB is Welding process is |
| A. | Friction brazing |
| B. | Furnace brazing |
| C. | Function brazing |
| D. | Finish brazing |
| Answer» B. Furnace brazing | |
| 6. |
Full form of FRW in Welding process are |
| A. | Friction Welding |
| B. | Furnace Welding |
| C. | Fusion Reaction welding |
| D. | None of them |
| Answer» A. Friction Welding | |
| 7. |
Ground Connection equipment is used for ______ welding |
| A. | Gas welding |
| B. | Arc Welding |
| C. | all |
| D. | none |
| Answer» B. Arc Welding | |
| 8. |
In Edge preparation selection of joint is based on the following factors |
| A. | Effect of warping |
| B. | Cost of designing of the product |
| C. | Characteristics of the product |
| D. | All of them |
| Answer» D. All of them | |
| 9. |
During edge preparation bevel angle is |
| A. | 15º |
| B. | 30º |
| C. | 40º |
| D. | 60º |
| Answer» C. 40º | |
| 10. |
The gap between two plates to be joined with a view to obtain full penetration are |
| A. | 1 to 3 mm |
| B. | 3 to 5 mm |
| C. | 5 to 8 mm |
| D. | 5 to 10 mm |
| Answer» B. 3 to 5 mm | |
| 11. |
For plates of thickness more than 16 mm which weld is used |
| A. | Square butt weld |
| B. | Single V butt weld |
| C. | Double V butt Weld |
| D. | Double U butt Weld |
| Answer» D. Double U butt Weld | |
| 12. |
For plates of thickness 3-5 mm which weld is used |
| A. | Square butt weld |
| B. | Single V butt weld |
| C. | Double V butt Weld |
| D. | Double U butt Weld |
| Answer» A. Square butt weld | |
| 13. |
The shape of slots made during edge preparation is based on |
| A. | Joint design |
| B. | Thickness of material |
| C. | Joint strength required |
| D. | All of the above |
| Answer» D. All of the above | |
| 14. |
For 0.5 to 15 mm thick plates are welded using |
| A. | Single-V & Single-U edges |
| B. | Double-V Edges |
| C. | Double-V & Double-U edge |
| D. | Square face edge |
| Answer» A. Single-V & Single-U edges | |
| 15. |
In welding using Single-V and Single-U edge beveling angle is of |
| A. | 15º to 30º |
| B. | 30º to 60º |
| C. | 60º to 80º |
| D. | 5º to 15º |
| Answer» C. 60º to 80º | |
| 16. |
In flat or down hand position the weld bed is |
| A. | Horizontal axis |
| B. | Vertical Axis |
| C. | all |
| D. | none |
| Answer» A. Horizontal axis | |
| 17. |
During the horizontal position of the weld, the slope would be up to |
| A. | 5º |
| B. | 10º |
| C. | 3º |
| D. | 8º |
| Answer» B. 10º | |
| 18. |
During the over-head position of the weld slope would be |
| A. | 0º-15º |
| B. | 0º-30º |
| C. | 0º-45º |
| D. | 0º-90º |
| Answer» C. 0º-45º | |
| 19. |
During the Inclined position of the weld Rotation between |
| A. | 0º-15º |
| B. | 0º-30º |
| C. | 0º-45º |
| D. | 0º-90º |
| Answer» D. 0º-90º | |
| 20. |
In the welding position, an angle between the line bisecting the weld crosssection and vertical plane passing through the weld root is known as |
| A. | Slope |
| B. | Rotation |
| C. | all |
| D. | none |
| Answer» B. Rotation | |
| 21. |
In the welding position, an angle between weld root line and horizontal reference plane is known as |
| A. | Slope |
| B. | Rotation |
| C. | all |
| D. | none |
| Answer» A. Slope | |
| 22. |
Choose the color of acetylene cylinder |
| A. | Maroon |
| B. | Yellow |
| C. | Black |
| D. | Red |
| Answer» A. Maroon | |
| 23. |
Choose the color of oxygen cylinder |
| A. | Maroon |
| B. | Yellow |
| C. | Black |
| D. | Red |
| Answer» C. Black | |
| 24. |
In oxy-acetylene gas welding heat is obtained by |
| A. | An electric ac |
| B. | Gas Flame |
| C. | Chemical |
| D. | None of these |
| Answer» B. Gas Flame | |
| 25. |
Which type of weld is used lying in the same plane |
| A. | Butt Joint |
| B. | Edge Joint |
| C. | Lap Joint |
| D. | Corner Joint |
| Answer» A. Butt Joint | |
| 26. |
Which type of butt joint is used to joint 9 mm to 13 mm thick plate |
| A. | Single-V or Single-U butt joint |
| B. | Double-V or double-U butt joint |
| C. | all |
| D. | none |
| Answer» A. Single-V or Single-U butt joint | |
| 27. |
In butt joint, which of the edge preparation is costlier |
| A. | V- shape |
| B. | U-Shape |
| C. | all |
| D. | none |
| Answer» B. U-Shape | |
| 28. |
In lap joint thickness of the sheets is up to |
| A. | 3 mm |
| B. | 4 mm |
| C. | 10 mm |
| D. | 15 mm |
| Answer» A. 3 mm | |
| 29. |
When two plates are to be joined by keeping their surface at about 90º to one-another |
| A. | Lap joint |
| B. | Butt Joint |
| C. | Tee Joint |
| D. | Corner Joint |
| Answer» C. Tee Joint | |
| 30. |
Full of the WPS is |
| A. | Welding Procedure Specification |
| B. | Welding Process System |
| C. | Welding Process Specification |
| D. | Welding Procedure System |
| Answer» A. Welding Procedure Specification | |
Done Studing? Take A Test.
Great job completing your study session! Now it's time to put your knowledge to the test. Challenge yourself, see how much you've learned, and identify areas for improvement. Don’t worry, this is all part of the journey to mastery. Ready for the next step? Take a quiz to solidify what you've just studied.