McqMate
These multiple-choice questions (MCQs) are designed to enhance your knowledge and understanding in the following areas: Manufacturing Engineering .
Chapters
| 1. |
Which of the following joint have high corrosion resistance? |
| A. | Welding joint |
| B. | Riveted joint |
| C. | Bolted joint |
| D. | None of the above |
| Answer» A. Welding joint | |
| 2. |
The metals having good weldability, in descending order are |
| A. | cast steel, iron, carbonsteel, castiron |
| B. | carbon steel, iron, cast steel, castiron |
| C. | iron, carbonsteel, cast steel, castiron |
| D. | castiron, iron, carbon steel, cast steel |
| Answer» A. cast steel, iron, carbonsteel, castiron | |
| 3. |
Which of the following is not included in weldability? |
| A. | Ability of mechanical soundness |
| B. | Serviceability of joint |
| C. | Strain relieving brittleness |
| D. | Metallurgical compatibility of metal |
| Answer» C. Strain relieving brittleness | |
| 4. |
On which of the following factor, does weldability not depend? |
| A. | Boiling point |
| B. | Melting point |
| C. | Thermal expansion |
| D. | Thermal conductivity |
| Answer» A. Boiling point | |
| 5. |
Which ofthe following is not away of correcting the metalwhich does not have good weldability properties? |
| A. | Procedure of welding |
| B. | Provision of fluxing material |
| C. | Provision of filler material |
| D. | Procedure of adding filler materials |
| Answer» D. Procedure of adding filler materials | |
| 6. |
Which of the following is an example of plastic welding? |
| A. | Gas welding |
| B. | Arc welding |
| C. | Forge welding |
| D. | Thermit welding |
| Answer» C. Forge welding | |
| 7. |
Which of the following is an example of fusion welding? |
| A. | Arc welding |
| B. | Forge welding |
| C. | Resistance welding |
| D. | Thermit welding with pressure |
| Answer» A. Arc welding | |
| 8. |
Which ofthe followingwelding process is usedforweldingof sheetmetals in automobile and air craft industries? |
| A. | Shield metal arc welding |
| B. | Gas tungsten arc welding |
| C. | Thermit welding |
| D. | Resistance welding |
| Answer» D. Resistance welding | |
| 9. |
In which of the following process, heat is created by blacksmith fire |
| A. | Forge welding |
| B. | Spot welding |
| C. | Projection welding |
| D. | Seam welding |
| Answer» A. Forge welding | |
| 10. |
The voltage needed in resistance welding does not depend upon |
| A. | Composition |
| B. | Area |
| C. | Thickness of weld |
| D. | Length of weld |
| Answer» D. Length of weld | |
| 11. |
In resistance welding, two electrodes are made of |
| A. | Aluminium |
| B. | Copper |
| C. | Iron |
| D. | Bronze |
| Answer» B. Copper | |
| 12. |
Arc welding machine uses only D.C. supply. |
| A. | True |
| B. | False |
| C. | all |
| D. | none |
| Answer» B. False | |
| 13. |
The negative pole of the electrode burns away faster than the positive pole. |
| A. | True |
| B. | False |
| C. | all |
| D. | none |
| Answer» B. False | |
| 14. |
Which of the following is affected by weld contour? |
| A. | Fatigue |
| B. | Creep |
| C. | Highpressureproperty |
| D. | Lowpressureproperty |
| Answer» A. Fatigue | |
| 15. |
Which of the following materials are not suited for cold welding? |
| A. | Brass |
| B. | Steel |
| C. | Silver |
| D. | Gold |
| Answer» B. Steel | |
| 16. |
Match the following
|
| A. | 1-3, 2-2, 3-1 |
| B. | 1-3, 2-1, 3-2 |
| C. | 1-2, 2-3, 3-1 |
| D. | 1-2, 2-1,3-3 |
| Answer» B. 1-3, 2-1, 3-2 | |
| 17. |
What is the capacity of an automatic welding machine? |
| A. | 100 to200A |
| B. | 300 to 400A |
| C. | 500 to700A |
| D. | 800 to 3000A |
| Answer» D. 800 to 3000A | |
| 18. |
What is the capacity of a light manual welding machine? |
| A. | 100 to200A |
| B. | 300 to 400A |
| C. | 500 to700A |
| D. | 60 amp to 500 amp |
| Answer» C. 500 to700A | |
| 19. |
What is the efficiency of an A.C. welding transformer? |
| A. | 0.6 |
| B. | 0.7 |
| C. | 0.8 |
| D. | 0.9 |
| Answer» C. 0.8 | |
| 20. |
What is the amount of electric energy required per kg in dc welding operation? |
| A. | 1-4 kWh |
| B. | 3-7 kWh |
| C. | 4-9 kWh |
| D. | 6-10 kWh |
| Answer» D. 6-10 kWh | |
| 21. |
During fabrication joining of two or more components are ___ |
| A. | Temporarily |
| B. | Permanently |
| C. | Temporarily or permanently both |
| D. | None of the above |
| Answer» C. Temporarily or permanently both | |
| 22. |
During fabrication which processes are included |
| A. | Welding |
| B. | Brazing |
| C. | Soldering |
| D. | All of the above |
| Answer» D. All of the above | |
| 23. |
The Weldability of the metals in descending order |
| A. | Iron, Steel, Cast iron, Low Alloy steel |
| B. | Steel, Cast iron, Iron, Low Alloy steel |
| C. | Iron, Cast iron, steel, low Alloy steel |
| D. | Steel, Iron, Cast iron, Low Alloy steel |
| Answer» A. Iron, Steel, Cast iron, Low Alloy steel | |
| 24. |
The Weldability of the metals in Ascending order |
| A. | Low Alloy Steel, Stainless Steel, Cast Iron, Steel |
| B. | Low Alloy Steel, Cast Iron, Steel, Stainless Steel |
| C. | Stainless Steel, Low Alloy Steel, Cast Iron, Steel |
| D. | Stainless Steel, Low Alloy Steel, Steel, Cast Iron |
| Answer» C. Stainless Steel, Low Alloy Steel, Cast Iron, Steel | |
| 25. |
During the welding power require to produce arc to join the metals are |
| A. | Low voltage low ampere |
| B. | Low voltage high ampere |
| C. | High voltage low ampere |
| D. | High voltage high ampere |
| Answer» B. Low voltage high ampere | |
| 26. |
Out of them which of the power source used in welding |
| A. | Bilopar welding generator, |
| B. | Multi operator D.C. welding sets |
| C. | Both of them |
| D. | None of them |
| Answer» C. Both of them | |
| 27. |
Static type power sources include |
| A. | Transformer, Motor-driven generator |
| B. | Rectifier, Engine-driven Generator |
| C. | Transformer, Rectifier |
| D. | Motor-driven generator, Engine-driven generator |
| Answer» C. Transformer, Rectifier | |
| 28. |
Rotating type power sources includes |
| A. | Transformer, Motor-driven generator |
| B. | Rectifier, Engine-driven Generator |
| C. | Transformer, Rectifier |
| D. | Motor-driven generator, Engine-driven generator |
| Answer» D. Motor-driven generator, Engine-driven generator | |
| 29. |
Which type of plates cannot be welded in single pass |
| A. | Thick plates |
| B. | Thin Plates |
| C. | all |
| D. | none |
| Answer» A. Thick plates | |
| 30. |
In power-sources Transformer can change polarity or not? |
| A. | Yes |
| B. | No |
| C. | all |
| D. | none |
| Answer» B. No | |
| 31. |
In arc welding voltage is dependent of _____ |
| A. | Arc length |
| B. | Arc gap |
| C. | Both of them |
| D. | None of them |
| Answer» C. Both of them | |
| 32. |
The percentage of __ minutes duration during which the power source with necessary output can be used without causing any damage |
| A. | 5 |
| B. | 10 |
| C. | 50 |
| D. | 60 |
| Answer» B. 10 | |
| 33. |
In power sources Current used is |
| A. | 50-1000 Amp |
| B. | 500-1000 Amp |
| C. | 100-500 Amp |
| D. | 50-200 Amp |
| Answer» A. 50-1000 Amp | |
| 34. |
Full form of OCV is |
| A. | Output current voltage |
| B. | Open command voltage |
| C. | Open current voltage |
| D. | Output command voltage |
| Answer» C. Open current voltage | |
| 35. |
Which type of Power source is Solid State |
| A. | Static type |
| B. | Rotating type |
| C. | Special type |
| D. | None of them |
| Answer» C. Special type | |
| 36. |
Which of power source is an engine-driven generator |
| A. | Static type |
| B. | Rotating type |
| C. | Special type |
| D. | None of them |
| Answer» B. Rotating type | |
| 37. |
Which of power source is Rectifier? |
| A. | Static type |
| B. | Rotating type |
| C. | Special type |
| D. | None of them |
| Answer» A. Static type | |
| 38. |
Full-Form of the MMAW is |
| A. | Manual metal arc welding |
| B. | Molted metal arc welding |
| C. | Mix Metal arc welding |
| D. | Metal arc welding |
| Answer» A. Manual metal arc welding | |
| 39. |
The voltage needed in resistance welding does not depend upon |
| A. | Composition |
| B. | Area |
| C. | Thickness |
| D. | Length |
| Answer» D. Length | |
| 40. |
Which type of process is also known as the fabrication process? |
| A. | Casting |
| B. | Forming |
| C. | Joining |
| D. | None of them |
| Answer» C. Joining | |
| 41. |
Arc length in arc welding should be equal to ___ |
| A. | Half the diameter of the electrode rod |
| B. | Rod diameter |
| C. | Twice the rod diameter |
| D. | None of the above |
| Answer» B. Rod diameter | |
| 42. |
In welding symbol, if the symbol is above the baseline then the welding is to be done at |
| A. | The arrow side |
| B. | Other side of the arrow |
| C. | Right side of the arrow |
| D. | Both side of the arrow |
| Answer» B. Other side of the arrow | |
| 43. |
Where the welding symbol is placed when the welding is to be done at the arrow side |
| A. | Below the baseline |
| B. | Above the baseline |
| C. | A & B both |
| D. | None of them |
| Answer» A. Below the baseline | |
| 44. |
For the vertical position of the weld fillet and other symbols should saw in which side |
| A. | Right |
| B. | Left |
| C. | Bottom |
| D. | Above |
| Answer» B. Left | |
| 45. |
The full form of DFW is |
| A. | Direct finish weld |
| B. | Direct fusion welding |
| C. | Diffusion welding |
| D. | Double fusion Welding |
| Answer» C. Diffusion welding | |
| 46. |
Full form of FB is Welding process is |
| A. | Friction brazing |
| B. | Furnace brazing |
| C. | Function brazing |
| D. | Finish brazing |
| Answer» B. Furnace brazing | |
| 47. |
Full form of FRW in Welding process are |
| A. | Friction Welding |
| B. | Furnace Welding |
| C. | Fusion Reaction welding |
| D. | None of them |
| Answer» A. Friction Welding | |
| 48. |
Ground Connection equipment is used for ______ welding |
| A. | Gas welding |
| B. | Arc Welding |
| C. | all |
| D. | none |
| Answer» B. Arc Welding | |
| 49. |
In Edge preparation selection of joint is based on the following factors |
| A. | Effect of warping |
| B. | Cost of designing of the product |
| C. | Characteristics of the product |
| D. | All of them |
| Answer» D. All of them | |
| 50. |
During edge preparation bevel angle is |
| A. | 15º |
| B. | 30º |
| C. | 40º |
| D. | 60º |
| Answer» C. 40º | |
Done Studing? Take A Test.
Great job completing your study session! Now it's time to put your knowledge to the test. Challenge yourself, see how much you've learned, and identify areas for improvement. Don’t worry, this is all part of the journey to mastery. Ready for the next step? Take a quiz to solidify what you've just studied.