McqMate
These multiple-choice questions (MCQs) are designed to enhance your knowledge and understanding in the following areas: Uncategorized topics .
| 601. |
The loop type-threshing drum is use for threshing |
| A. | Wheat |
| B. | Paddy |
| C. | Gram |
| D. | Soyabean |
| Answer» B. Paddy | |
| 602. |
The knives of shredders are rotated in |
| A. | Horizontal plane with direction of travel |
| B. | Vertical plane with direction of travel |
| C. | Both (a) & (b) |
| D. | None of these |
| Answer» B. Vertical plane with direction of travel | |
| 603. |
The expected annual use of seed drill is |
| A. | 800 hours |
| B. | 1000 hours |
| C. | 1200 hours |
| D. | 1500 hours |
| Answer» D. 1500 hours | |
| 604. |
277 per hectare application rate of low volume sprayer is |
| A. | 2 litres |
| B. | 3 litres |
| C. | 4 litres |
| D. | 5 litres |
| Answer» D. 5 litres | |
| 605. |
The true specific gravity of dominant material is |
| A. | 1.65 |
| B. | 2.65 |
| C. | 3.65 |
| D. | 4.65 |
| Answer» B. 2.65 | |
| 606. |
The actual area irrigated in a year from outlet is |
| A. | Irrigation period |
| B. | Intensity of irrigation |
| C. | Irrigation frequency |
| D. | None of these |
| Answer» B. Intensity of irrigation | |
| 607. |
The pump is used in power-operated sprayer is |
| A. | Plunger type |
| B. | Diaphragm type |
| C. | Gear type |
| D. | Piston type |
| Answer» C. Gear type | |
| 608. |
Thing layer drying includes |
| A. | Batch type dryer |
| B. | LSU dryer |
| C. | Flat bed dryer |
| D. | All are correct |
| Answer» C. Flat bed dryer | |
| 609. |
A single piece share with curved cutting edge is |
| A. | Slip nose share |
| B. | Bar point share |
| C. | Shin shared |
| D. | Slip share |
| Answer» D. Slip share | |
| 610. |
Range of pressure angle in spur gear is |
| A. | 5?8 |
| B. | 5?12 |
| C. | 14?20 |
| D. | 20?25 |
| Answer» C. 14?20 | |
| 611. |
The area of land draining into a watercourse at a given location is known as |
| A. | The Catchments area |
| B. | Drainage area |
| C. | Drainage basin |
| D. | All are correct |
| Answer» D. All are correct | |
| 612. |
The size of mould board plough is expressed by |
| A. | Width of cut |
| B. | Depth of cut |
| C. | Size of furrow |
| D. | Plough width |
| Answer» A. Width of cut | |
| 613. |
The useful life of stationary engine is |
| A. | 10 years |
| B. | 15 years |
| C. | 12 years |
| D. | 20 years |
| Answer» A. 10 years | |
| 614. |
In batch type dryer, the maximum depth of grain is about |
| A. | 200 cm |
| B. | 225 cm |
| C. | 250 cm |
| D. | 300 cm |
| Answer» C. 250 cm | |
| 615. |
Top link of trctor is also known as |
| A. | Tension link |
| B. | Mast |
| C. | Pressure link |
| D. | All are correct |
| Answer» D. All are correct | |
| 616. |
Wet dusting is beneficial for |
| A. | Drought area |
| B. | Semi-arid area |
| C. | Low rainfall areas |
| D. | Heavy rainfall areas |
| Answer» A. Drought area | |
| 617. |
Main part of thresher that removes seeds from grain head is |
| A. | Cylinder |
| B. | Concave |
| C. | Pegs on cylinder |
| D. | Sieve |
| Answer» A. Cylinder | |
| 618. |
The operational life of a pair of rubber rolls is estimated at |
| A. | 80 tonne |
| B. | 90 tonnes |
| C. | 100 tonne |
| D. | 120 tonnes |
| Answer» C. 100 tonne | |
| 619. |
In seed drill, the depth of seed placement for better germination should be |
| A. | 3 cm |
| B. | 5 cm |
| C. | 7 cm |
| D. | 10 cm |
| Answer» B. 5 cm | |
| 620. |
In floating type biogas plant, gas holder is made of |
| A. | Metal |
| B. | Wood |
| C. | Cement and bricks |
| D. | All are correct |
| Answer» A. Metal | |
| 621. |
Pneumatic governor is used on |
| A. | Diesel engine |
| B. | Petrol engine |
| C. | Both (a) & (b) |
| D. | None of these |
| Answer» C. Both (a) & (b) | |
| 622. |
The share of MB plough is made of |
| A. | Cast iron |
| B. | High carbon steel |
| C. | Chilled cast iron |
| D. | White metal |
| Answer» C. Chilled cast iron | |
| 623. |
A vertical angle of the projection of sun's rays on the horizontal plane and direction of sun's rays is called |
| A. | Zenith angle |
| B. | Altitude angle |
| C. | Hour angle |
| D. | Incident angle |
| Answer» B. Altitude angle | |
| 624. |
The term turrel is associated with |
| A. | Sickle |
| B. | Reaper |
| C. | Mower |
| D. | Combine |
| Answer» A. Sickle | |
| 625. |
The moisture content for safe storage corn is about |
| A. | 10 per cent |
| B. | 13 per cent |
| C. | 14 per cent |
| D. | 16 per cent |
| Answer» B. 13 per cent | |
| 626. |
A shaft of disc harrow on which the number of discs is mounted is |
| A. | Standard |
| B. | Arbor bolt |
| C. | Spacer |
| D. | Scraper |
| Answer» B. Arbor bolt | |
| 627. |
The specific fuel consumption of diesel engine is |
| A. | 180 gm/bhp/hr |
| B. | 200 gm/bhp/hr |
| C. | 150 gm/bhp/hr |
| D. | 290 gm/bhp/hr |
| Answer» B. 200 gm/bhp/hr | |
| 628. |
Disgester diameter of biogas plants ranges from |
| A. | 1-3 metres |
| B. | 1.2-4 metres |
| C. | 1.1-6 metres |
| D. | 1.6-8 metres |
| Answer» C. 1.1-6 metres | |
| 629. |
In disc plough, the penetration of disc improves but width of cut reduces due to |
| A. | Increasing tilt angle |
| B. | Reducing tilt angle |
| C. | Increasing disc angle |
| D. | Reducing disc angle |
| Answer» C. Increasing disc angle | |
| 630. |
Hot plugs are used in |
| A. | Diesel tractor |
| B. | Petrol tractors |
| C. | Powerine tractors |
| D. | All are correct |
| Answer» C. Powerine tractors | |
| 631. |
A wheel used for maintaining uniform depth of ploughing in different soils is |
| A. | Transport wheel |
| B. | Land wheel |
| C. | Furrow wheel |
| D. | Gauge wheel |
| Answer» D. Gauge wheel | |
| 632. |
The metering mechanism used for mustard seed is |
| A. | Fluted roller |
| B. | Vertical plate type |
| C. | Cell fill type |
| D. | Stud roller type |
| Answer» D. Stud roller type | |
| 633. |
When crankshaft of the engine completes one cycle, the camshaft completes |
| A. | Two revolution |
| B. | Half revolution |
| C. | Equal revolution of crankshaft |
| D. | None of these |
| Answer» B. Half revolution | |
| 634. |
Cetane number for commercial diesel fuel varies from |
| A. | 20-40 |
| B. | 30-60 |
| C. | 60-90 |
| D. | 90-100 |
| Answer» B. 30-60 | |
| 635. |
Detached particles are transported by the mechanism of |
| A. | Displacement caused by physical impact |
| B. | Entrainment caused by overland flow |
| C. | Both (a) and (b) |
| D. | None of these |
| Answer» C. Both (a) and (b) | |
| 636. |
A type of valve used in hydraulic system is |
| A. | Control valve |
| B. | Relief valve |
| C. | Priority valve |
| D. | All are correct |
| Answer» D. All are correct | |
| 637. |
The energy obtained from the sun is |
| A. | Atomic energy |
| B. | Tidal energy |
| C. | Solar energy |
| D. | Wave energy |
| Answer» C. Solar energy | |
| 638. |
Ignition temperature of IC engines varies from |
| A. | 300-500?C |
| B. | 500-700?C |
| C. | 500-900?C |
| D. | 700-1000?C |
| Answer» C. 500-900?C | |
| 639. |
Removal of burnt gases from engine cylinder is called |
| A. | Pre-ignition |
| B. | Detonation |
| C. | Scavenging |
| D. | Supercharging |
| Answer» C. Scavenging | |
| 640. |
For petrol engine, the maximum power obtained from one kg of fuel is |
| A. | 10.5-13.8 kg |
| B. | 11-15 kg |
| C. | 12-16 kg |
| D. | 15-20 kg |
| Answer» A. 10.5-13.8 kg | |
| 641. |
Crown wheel is a part of |
| A. | Clutch system |
| B. | Steering system |
| C. | Differential system |
| D. | Cooling system |
| Answer» C. Differential system | |
| 642. |
A type of share provided with adjustable bar is |
| A. | Slip nose share |
| B. | Bar point share |
| C. | Shin shared |
| D. | Slip share |
| Answer» B. Bar point share | |
| 643. |
Specific gravity of grains is determined by |
| A. | Pycnometer |
| B. | Specific gravity bottle |
| C. | Both (a) and (b) |
| D. | None of these |
| Answer» C. Both (a) and (b) | |
| 644. |
An implement that pulled and guided by single hitch point of a tractor is |
| A. | Trailed implement |
| B. | Mounted implement |
| C. | Semi mounted implements |
| D. | All are correct |
| Answer» A. Trailed implement | |
| 645. |
The capacity of RPEC dryer is about |
| A. | Half tonne per hour |
| B. | One tonne per hour |
| C. | Two tonne per hour |
| D. | All are correct |
| Answer» D. All are correct | |
| 646. |
Semi-solid lubricant is |
| A. | Gear oil |
| B. | Engine oil |
| C. | Grease |
| D. | None of these |
| Answer» C. Grease | |
| 647. |
Power train indicates |
| A. | PTO drive |
| B. | Injection system |
| C. | Complete power transmission path |
| D. | Reduction unit |
| Answer» C. Complete power transmission path | |
| 648. |
The use of reflector in solar heating devices is to |
| A. | Increase efficiency |
| B. | Decrease efficiency |
| C. | Create greenhouse effect |
| D. | None of these |
| Answer» A. Increase efficiency | |
| 649. |
LSU dryer was developed in/at |
| A. | 1949 (USA) |
| B. | 1950 (England) |
| C. | 1965 (Japan) |
| D. | None of these |
| Answer» A. 1949 (USA) | |
| 650. |
Nudging system is used for |
| A. | Rising implement |
| B. | Lower the implement |
| C. | Both (a) & (b) |
| D. | None of these |
| Answer» C. Both (a) & (b) | |
Done Studing? Take A Test.
Great job completing your study session! Now it's time to put your knowledge to the test. Challenge yourself, see how much you've learned, and identify areas for improvement. Don’t worry, this is all part of the journey to mastery. Ready for the next step? Take a quiz to solidify what you've just studied.