McqMate
These multiple-choice questions (MCQs) are designed to enhance your knowledge and understanding in the following areas: Electrical Engineering .
Chapters
| 101. |
A transformer can have regulation closer to zero |
| A. | on full-load |
| B. | on overload |
| C. | on leading power factor |
| D. | on zero power factor |
| Answer» C. on leading power factor | |
| 102. |
A transformer transforms |
| A. | voltage |
| B. | current |
| C. | current and voltage |
| D. | power |
| Answer» D. power | |
| 103. |
Which of the following is not the standard voltage for power supply in India ? |
| A. | llkV |
| B. | 33kV |
| C. | 66 kV |
| D. | 122 kV |
| Answer» D. 122 kV | |
| 104. |
Reduction in core losses and increase in permeability are obtained with transformer employing |
| A. | core built-up of laminations of cold rolled grain oriented steel |
| B. | core built-up of laminations of hot rolled sheet |
| C. | either of the above |
| D. | none of the above |
| Answer» A. core built-up of laminations of cold rolled grain oriented steel | |
| 105. |
In a power or distribution transformer about 10 per cent end turns are heavily insulated |
| A. | to withstand the high voltage drop due to line surge produced by the shunting capacitance of the end turns |
| B. | to absorb the line surge voltage and save the winding of transformer fromdamage |
| C. | to reflect the line surge and save the winding of a transformer from damage |
| D. | none of the above |
| Answer» A. to withstand the high voltage drop due to line surge produced by the shunting capacitance of the end turns | |
| 106. |
For given applied voltage, with the increase in frequency of the applied voltage |
| A. | eddy current loss will decrease |
| B. | eddy current loss will increase |
| C. | eddy current loss will remain unchanged |
| D. | none of the above |
| Answer» C. eddy current loss will remain unchanged | |
| 107. |
Losses which occur in rotating electric machines and do not occur in transformers are |
| A. | friction and windage losses |
| B. | magnetic losses |
| C. | hysteresis and eddy current losses |
| D. | copper losses |
| Answer» A. friction and windage losses | |
| 108. |
In a given transformer for a given applied voltage, losses which remainconstant irrespective of load changes are |
| A. | hysteresis and eddy current losses |
| B. | friction and windage losses |
| C. | copper losses |
| D. | none of the above |
| Answer» A. hysteresis and eddy current losses | |
| 109. |
Which of the following statements regarding an idel single-phase transformerhaving a turn ratio of 1 : 2 and drawing a current of 10 A from 200 V A.C. supply is incorrect ? |
| A. | Its secondary current is 5 A |
| B. | Its secondary voltage is 400 V |
| C. | Its rating is 2 kVA |
| D. | Its secondary current is 20 A |
| Answer» D. Its secondary current is 20 A | |
| 110. |
The secondary of a current transformer is always short-circuited underoperating conditions because it |
| A. | avoids core saturation and high voltage induction |
| B. | is safe to human beings |
| C. | protects the primary circuit |
| D. | none of the above |
| Answer» A. avoids core saturation and high voltage induction | |
| 111. |
In a transformer the resistance between its primary and secondary should be |
| A. | zero |
| B. | 10 Q |
| C. | 1000 Q |
| D. | infinity |
| Answer» D. infinity | |
| 112. |
A good voltage regulation of a transformer means |
| A. | output voltage fluctuation from no load to full load is least |
| B. | output voltage fluctuation with power factor is least |
| C. | difference between primary and secondary voltage is least |
| D. | difference between primary and secondary voltage ismaximum |
| Answer» A. output voltage fluctuation from no load to full load is least | |
| 113. |
For a transformer, operating at constant load current, maximum efficiency will occur at |
| A. | 0.8 leading power factor |
| B. | 0.8 lagging power factor |
| C. | zero power factor |
| D. | unity power factor |
| Answer» D. unity power factor | |
| 114. |
Which of the following protection is normally not provided on smalldistribution transformers ? |
| A. | Overfluxing protection |
| B. | Buchholz relay |
| C. | Overcurrent protection |
| D. | All of the above |
| Answer» B. Buchholz relay | |
| 115. |
Which of the following acts as a protection against high voltage surges due to lightning and switching ? |
| A. | Horn gaps |
| B. | Thermal overload relays |
| C. | Breather |
| D. | Conservator |
| Answer» A. Horn gaps | |
| 116. |
The efficiency of two identical transformers under load conditionscan be determined by |
| A. | short-circuit test |
| B. | back-to-back test |
| C. | open circuit test |
| D. | any of the above |
| Answer» B. back-to-back test | |
| 117. |
Which of the following insulating materials can withstand the highest temperature safely ? |
| A. | Cellulose |
| B. | Asbestos |
| C. | Mica |
| D. | Glass fibre |
| Answer» C. Mica | |
| 118. |
Which of the following parts of a transformer is visible from outside ? |
| A. | Bushings |
| B. | Core |
| C. | Primary winding |
| D. | Secondary winding |
| Answer» A. Bushings | |
| 119. |
The noise produced by a transformer is termed as |
| A. | zoom |
| B. | hum |
| C. | ringing |
| D. | buzz |
| Answer» B. hum | |
| 120. |
Which of the following loss in a transformer is zero even at full load ? |
| A. | Core loss |
| B. | Friction loss |
| C. | Eddy current loss |
| D. | Hysteresis loss |
| Answer» B. Friction loss | |
| 121. |
Which of the following is the most likely source of harmonics in a transformer ? |
| A. | poor insulation |
| B. | Overload |
| C. | loose connections |
| D. | Core saturation |
| Answer» D. Core saturation | |
| 122. |
If a transformer is continuously operated the maximum temperature rise will occur in |
| A. | core |
| B. | windings |
| C. | tank |
| D. | any of the above |
| Answer» B. windings | |
| 123. |
The hum in a transformer is mainly attributed to |
| A. | load changes |
| B. | oil in the transformer |
| C. | magnetostriction |
| D. | mechanical vibrations |
| Answer» C. magnetostriction | |
| 124. |
The maximum load that a power transformer can carry is limited by its |
| A. | temperature rise |
| B. | dielectric strength of oil |
| C. | voltage ratio |
| D. | copper loss |
| Answer» C. voltage ratio | |
| 125. |
The efficiency of a transformer, under heavy loads, is comparatively low because |
| A. | copper loss becomes high in proportion to the output |
| B. | iron loss is increased considerably |
| C. | voltage drop both in primary and secondary becomes large |
| D. | secondary output is much less as compared to primary input |
| Answer» A. copper loss becomes high in proportion to the output | |
| 126. |
An open-circuit test on a transformer is conducted primarily to measure |
| A. | insulation resistance |
| B. | copper loss |
| C. | core loss |
| D. | total loss |
| Answer» C. core loss | |
| 127. |
A no-load test is performed on a transformer to determine |
| A. | core loss |
| B. | copper loss |
| C. | efficiency |
| D. | magnetising current and loss |
| Answer» D. magnetising current and loss | |
| 128. |
The voltage transformation ratio of a transformer is equal to the ratio of |
| A. | primary turns to secondary turns |
| B. | secondary current to primary current |
| C. | secondary induced e.m.f. to primary induced e.m.f. |
| D. | secondary terminal voltage to primary applied voltage |
| Answer» C. secondary induced e.m.f. to primary induced e.m.f. | |
| 129. |
Part of the transformer which is most subject to damage from overheating is |
| A. | iron core |
| B. | copper winding |
| C. | winding insulation |
| D. | frame or case |
| Answer» C. winding insulation | |
| 130. |
If a transformer is switched on to a voltage more than the rated voltage |
| A. | its power factor will deteriorate |
| B. | its power factor will increase |
| C. | its power factor will remain unaffected |
| D. | its power factor will be zero |
| Answer» A. its power factor will deteriorate | |
| 131. |
Auto-transformer makes effective saving on copper and copper losses, whenits transformation ratio is |
| A. | approximately equal to one |
| B. | less than one |
| C. | great than one |
| D. | none of the above |
| Answer» A. approximately equal to one | |
| 132. |
Minimum voltage regulation occurs when the power factor of the load is |
| A. | unity |
| B. | lagging |
| C. | leading |
| D. | zero |
| Answer» C. leading | |
| 133. |
In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of |
| A. | less than 15 A |
| B. | more than 15 A |
| C. | 15 A |
| D. | none of the above |
| Answer» A. less than 15 A | |
Done Studing? Take A Test.
Great job completing your study session! Now it's time to put your knowledge to the test. Challenge yourself, see how much you've learned, and identify areas for improvement. Don’t worry, this is all part of the journey to mastery. Ready for the next step? Take a quiz to solidify what you've just studied.