McqMate
These multiple-choice questions (MCQs) are designed to enhance your knowledge and understanding in the following areas: Mechanical Engineering .
451. |
The welding of steel structures on the site of a building is done by |
A. | Arc welding |
B. | Spot welding |
C. | Projection welding |
D. | Thermit welding |
E. | TIG welding |
Answer» A. Arc welding |
452. |
The advantage of a pneumatically operated control system is |
A. | It can be used in hazardous atmosphere |
B. | Simplicity of components |
C. | Easily maintained |
D. | Relatively inexpensive |
E. | All of the above |
Answer» E. All of the above |
453. |
The surface speed of grinding wheel in case of centreless grinding is |
A. | 1000 - 1500 M/min |
B. | 15 - 75 M/min |
C. | 1500 - 1800 M/min |
D. | 100 - 500 M/min |
E. | 500 - 800 M/min |
Answer» C. 1500 - 1800 M/min |
454. |
An examiner has given the following as parts of drill bit. Find which one is not correct |
A. | Cutting edge |
B. | Eye |
C. | Shank |
D. | Point |
E. | Dead centre |
Answer» B. Eye |
455. |
A 20 number crucible |
A. | Will have height of 20 cm |
B. | Can take 20 cc of molten material |
C. | Will have capacity to melt 20 kg of copper |
D. | Will have internal diameter of 20 cm |
E. | Can produce castings of 20 kg only |
Answer» C. Will have capacity to melt 20 kg of copper |
456. |
For the measurement of pressure corrosive and highly viscous liquids with the halp of pressure gauge |
A. | Gauge scale is modified |
B. | Seal pots are used |
C. | Bourdon tube of the gauge is changed |
D. | Necessary corrections are applied |
E. | Pressure gauge is never used in such situations |
Answer» B. Seal pots are used |
457. |
2% Nickel in steel makes it suitable for |
A. | Boiler plates, rivets etc |
B. | Electronic valves |
C. | Connecting rods |
D. | Anti corrosion characteristics |
E. | Turbine blade |
Answer» A. Boiler plates, rivets etc |
458. |
IS code considers how many types of steels for designating carbon content in the steel? |
A. | 1 |
B. | 4 |
C. | Parting off |
D. | 2 |
E. | 3 |
Answer» B. 4 |
459. |
In a turning operation on a horizontal axis lathe, the forces on tool act |
A. | only in horizontal plane in the directions of feed and cut |
B. | only in vertical plane in the direction of feed and vertically |
C. | only in vertical plane in the direction of feed and radially |
D. | None of the above |
E. | Parting off |
Answer» B. only in vertical plane in the direction of feed and vertically |
460. |
In a stationary type mechanical seal the sealing ring is generally located |
A. | In machine housing |
B. | Along machine shaft |
C. | Independently |
D. | None of the above |
E. | None of the above |
Answer» A. In machine housing |
461. |
Gold ornaments are generally produced by |
A. | Pressed casting |
B. | Slush casting |
C. | Investment casting |
D. | Die-casting |
E. | Centrifugal casting |
Answer» A. Pressed casting |
462. |
In manufacturing ERW tube the type of welding generally used is |
A. | Induction welding |
B. | Thermit welding |
C. | Electrical resistance welding |
D. | Gas welding |
E. | Are welding |
Answer» C. Electrical resistance welding |
463. |
To clean a hand file |
A. | It is rubbed on stone |
B. | File card is used |
C. | It is dipped in dilute acid |
D. | It is rubbed on wood |
E. | It is dipped in water |
Answer» B. File card is used |
464. |
During MIG welding the metal is transferred in the form of |
A. | Metal is not transferred during MIG welding |
B. | Solution |
C. | Continuous flow of molten metal |
D. | A fine spray of metal |
E. | Electron beam |
Answer» D. A fine spray of metal |
465. |
In Rockwell test for hardness on B scale |
A. | A diamond cone is used |
B. | A mechanite ball is used |
C. | A steel hammer is used |
D. | A steel ball is used |
E. | A plastic hammer is used |
Answer» D. A steel ball is used |
466. |
For soldering of brass and copper, the flux used is |
A. | Zinc chloride |
B. | Hydrochloric acid |
C. | Cupric acid |
D. | Ammonium chloride |
E. | None of the above |
Answer» A. Zinc chloride |
467. |
During metal cutting operation on machine tools, the major portion of heat is carried away by |
A. | Chip and tool have identical heat dissipation |
B. | Chip |
C. | Work piece |
D. | Chip tool and work piece have identical proportion of heat dissipation |
E. | Tool |
Answer» B. Chip |
468. |
The purpose of an automatic process control system generally is |
A. | To automatically produce goods |
B. | To automatically detect inferior quality goods |
C. | To automatically process the raw materials |
D. | To direct the forces that give stable plant and process operation by maintaining desired values of process variables or conditions |
E. | None of the above |
Answer» D. To direct the forces that give stable plant and process operation by maintaining desired values of process variables or conditions |
469. |
Which of the following process has highest power consumption in kW/cm2/min? |
A. | Plasma arc machining |
B. | Electron beam machining |
C. | Abrasive jet machining |
D. | Electro chemical machining |
E. | Ultrasonic machining |
Answer» B. Electron beam machining |
470. |
Cold heading is a process of |
A. | Electro-machining process |
B. | Explosive forming |
C. | High energy rate forming |
D. | Pneumatic mechanical forming |
E. | Chipless machining |
Answer» E. Chipless machining |
471. |
For soft steel the cutting speed for lathe operations is around |
A. | 100 m/min |
B. | 30 m/min |
C. | 150 m/min |
D. | 300 m/min |
E. | 1000 m/min |
Answer» B. 30 m/min |
472. |
In induction hardening the depth of hardening can be controlled by controlling |
A. | voltage |
B. | power factor |
C. | frequency |
D. | current |
E. | Parting off |
Answer» C. frequency |
473. |
The surface of a slip gauge is produced by |
A. | Milling |
B. | Grinding |
C. | Lapping |
D. | Burnishing |
E. | Any of the above |
Answer» C. Lapping |
474. |
The transmission lag in mercury thermometers is generally |
A. | Low |
B. | Average |
C. | Negligible |
D. | Very high |
E. | High |
Answer» A. Low |
475. |
Brass is |
A. | Copper aluminium alloy |
B. | Copper-nickel alloy |
C. | Copper-zinc alloy |
D. | Copper-tin alloy |
E. | Copper-lead alloy |
Answer» C. Copper-zinc alloy |
476. |
Photoelectric transducers are used for the measurement of any phenomenon which can be used to produce |
A. | Variation in current |
B. | Variation in voltage |
C. | Variation in light intensity |
D. | Variation in flux density |
E. | Any of the above |
Answer» C. Variation in light intensity |
477. |
Chisels for metal cutting are |
A. | Hardened in the middle |
B. | Hardened at cutting edge |
C. | Hardened all over |
D. | Hardened at random |
E. | Never hardened |
Answer» C. Hardened all over |
478. |
Kind of tools used to undercut corners on a job that is to be hardened and ground is |
A. | Vee shaped tool |
B. | Form tool |
C. | Knurling tool |
D. | Roundnose tool |
E. | Parting tool |
Answer» D. Roundnose tool |
479. |
If a drill has different lengths of cutting edges |
A. | Cutting edge will be over size |
B. | The drilled hole will be rough |
C. | The drilled hole will not be circular |
D. | The drilled hole will be smooth |
E. | Cutting edge will become blunt rapidly |
Answer» E. Cutting edge will become blunt rapidly |
480. |
Plastic gears are used in |
A. | Toys |
B. | Instruments |
C. | Low load applications |
D. | Low noise applications |
E. | Any of the above |
Answer» E. Any of the above |
481. |
Fine sand is used for preparing the moulds for |
A. | Symmetrical castings |
B. | Large castings |
C. | Small castings |
D. | Non-ferrous castings |
E. | Centrifugal castings |
Answer» C. Small castings |
482. |
Which one of the following measuring instruments is supposed to be most accurate? |
A. | Micrometer |
B. | Vernier dial gauge |
C. | Optical projector |
D. | Steel scale |
E. | Vernier caliper |
Answer» C. Optical projector |
483. |
A diamond point chisel is used for |
A. | V-shaped grooves |
B. | Spherical surfaces |
C. | Flat surfaces |
D. | Convex surfaces |
E. | Round surfaces |
Answer» A. V-shaped grooves |
484. |
Which of the following is a chipless machining process? |
A. | Metal spinning |
B. | Knurling |
C. | Hobbing |
D. | Lapping |
E. | None of the above |
Answer» A. Metal spinning |
485. |
With HSS tools the maximum safe operating temperature is of the order of |
A. | 200?C |
B. | 440?C |
C. | 640?C |
D. | 540?C |
E. | 340?C |
Answer» D. 540?C |
486. |
Relief angle on HSS tools usually vary from |
A. | 11 to 15? |
B. | 22 to 27? |
C. | 16 to 150? |
D. | 28 to 30? |
E. | 3 to 10? |
Answer» E. 3 to 10? |
487. |
Spiral flutes are provided on drill bits to |
A. | Help from the cutting edge of the drill point |
B. | Curl the chip tightly for easier removal |
C. | Provide passage for coolant supply |
D. | All of the above |
E. | None of the above |
Answer» D. All of the above |
488. |
Which one of the following is supposed to be least accurate? |
A. | Surface plate |
B. | Air gauge |
C. | Optical projector |
D. | Vernier micrometer |
E. | Steel scale |
Answer» E. Steel scale |
489. |
Automobile gears are generally made of |
A. | Alloy steel |
B. | Cast iron |
C. | Nitrided steel |
D. | Cast steel |
E. | Non-ferrous materials |
Answer» A. Alloy steel |
490. |
Marform is |
A. | Is a foming process on lathe in which movement of tool is neither governed by cross slide nor by compound slide |
B. | A work holding device in which plane of rotation can be changed while working |
C. | A darwing process that forms metal sheet by using a movable steel punch and a rubber headed ram |
D. | Is a forming tool and on lathe machine to generate spherical surfaces |
E. | Is a gauge used to check regular surfaces |
Answer» C. A darwing process that forms metal sheet by using a movable steel punch and a rubber headed ram |
491. |
For aluminium, the cutting speed on lathe is around |
A. | 150 m/min |
B. | 300 m/min |
C. | 100 m/min |
D. | 1000 m/min |
E. | 30 m/min |
Answer» B. 300 m/min |
492. |
Which of the following defect results due to mixing of two streams of molten metal that are too cold to fuse properly? |
A. | Cold shut |
B. | Swell |
C. | Honey coming |
D. | Scab |
E. | Shrinkage |
Answer» A. Cold shut |
493. |
The range of voltage (open circuit) in are welding is generally |
A. | 20 - 40 V |
B. | 100 - 150 V |
C. | 40 - 90 V |
D. | 150 - 230 V |
E. | 400 - 440 V |
Answer» C. 40 - 90 V |
494. |
A Bourdon tube is generally made of |
A. | Monel metal |
B. | Beryllium copper alloy |
C. | Phosphor bronze |
D. | Stainless steel |
E. | Any of the above |
Answer» E. Any of the above |
495. |
The chemical used in generating acetylene is |
A. | Charcoal |
B. | Calcium carbonate |
C. | Calcium carbide |
D. | Carbon |
E. | Crushed bone |
Answer» E. Crushed bone |
496. |
Which one of the following is not a part of micrometer |
A. | Sleeve |
B. | Spindle |
C. | Thimble |
D. | Anvil |
E. | Beam |
Answer» E. Beam |
497. |
Plug rolling is used to |
A. | Reduce the wall thickness and increase the diameter of tubes already made |
B. | Remove out of roundness of pipes |
C. | Increase the wall thickness of pipes at ends |
D. | Reduce the diameter of pipe |
E. | Cut threads at the ends of pipes |
Answer» A. Reduce the wall thickness and increase the diameter of tubes already made |
498. |
Burr is |
A. | Boundary between finished and unifinished portion on a work piece |
B. | Sharp edge remaining on the metal after curring, stamping or machining |
C. | A marking or work piece to identify for correct position on a work piece |
D. | Burnt surface of a casting |
E. | Unmachined portion of work piece |
Answer» B. Sharp edge remaining on the metal after curring, stamping or machining |
499. |
Which process is used for manufacturing the body of a carburettor? |
A. | Die casting |
B. | Fine sand casting |
C. | Electro forming |
D. | Sintering |
E. | Metal spraying |
Answer» A. Die casting |
500. |
The silver point temperature is |
A. | 760?C |
B. | 1500.5?C |
C. | 500?C |
D. | 960.5?C |
E. | 1100.5?C |
Answer» D. 960.5?C |
Done Studing? Take A Test.
Great job completing your study session! Now it's time to put your knowledge to the test. Challenge yourself, see how much you've learned, and identify areas for improvement. Don’t worry, this is all part of the journey to mastery. Ready for the next step? Take a quiz to solidify what you've just studied.