McqMate
These multiple-choice questions (MCQs) are designed to enhance your knowledge and understanding in the following areas: Mechanical Engineering .
401. |
Which of the following is an accessory for lathe machine? |
A. | Lead screw |
B. | Cone pulley |
C. | Tool post |
D. | Coolant pump |
E. | None of the above |
Answer» D. Coolant pump |
402. |
Loams sand generally has |
A. | 50% clay and 18% moisture |
B. | 60% clay and 30% moisture |
C. | 34% clay and 5% moisture |
D. | 70% clay and 30% moisture |
E. | 40% clay and 10% moisture |
Answer» A. 50% clay and 18% moisture |
403. |
Straight shears are used for |
A. | Straight line cutting of sheets |
B. | Making circular cuts |
C. | Parting off |
D. | Making irregular cuts |
Answer» A. Straight line cutting of sheets |
404. |
Duration which operation on a lathe machine, the spindle speed is usually the least? |
A. | Finish turning |
B. | Drilling |
C. | Parting off |
D. | Rough turning |
E. | Knurling |
Answer» E. Knurling |
405. |
Music wire |
A. | Is a standard wire for gauge determination |
B. | Is a resistance wire used in instruments |
C. | Is fine wire used in musical instruments manufacture springs |
D. | None of above |
E. | Is a carbon steel wire used to manufacture springs |
Answer» E. Is a carbon steel wire used to manufacture springs |
406. |
In abrasive jet machining the achievable tolerances are nearly |
A. | 500 |
B. | 1 |
C. | 0.1 |
D. | 250 |
E. | 50 |
Answer» E. 50 |
407. |
A knee is a part of |
A. | Lathe |
B. | Jig boring machine |
C. | Milling machine |
D. | Breaching machine |
E. | Shaper |
Answer» C. Milling machine |
408. |
The operation of cutting multiple holes is called |
A. | perforating |
B. | Parting off |
C. | notching |
D. | trimming |
E. | lancing |
Answer» A. perforating |
409. |
Gear made by sand casting are used in |
A. | Automobiles |
B. | Toys |
C. | Diesel locomotives |
D. | Concrete mixers |
E. | Machine tools |
Answer» D. Concrete mixers |
410. |
A bench vice is used for |
B. | Filing the job |
C. | Tapping the job |
D. | Clamping the job |
E. | Parting off |
Answer» D. Clamping the job |
411. |
Broaching is primarily done for |
A. | mass production |
B. | hard materials |
C. | better finish |
D. | cylindrical jobs |
E. | Parting off |
Answer» A. mass production |
412. |
For simple turning operation of lathe, the cutting speed is specified as 70 metres per minute. The cutting tool may be expected to be |
A. | Carbide |
B. | Higher speed steel |
C. | Carbon steel |
D. | Mild steel |
E. | Diamond |
Answer» A. Carbide |
413. |
Simple indexing using a dividing head of turn ratio 40 for 6 division would be |
A. | 14 holes in 21 hole circle plate |
B. | 26 holes in 21 hole circle plate |
C. | 6 turns and holes in 21 hole circle plate |
D. | 6 turns and 14 holes in 30 hole circle plate |
E. | 6 turns |
Answer» C. 6 turns and holes in 21 hole circle plate |
414. |
In instrumentation, registering is |
A. | Production of continuous record on an instrument |
B. | Conversion of signal from one form to another |
C. | Indication by numbers or some other symbol of discrete increments, the value of some quantity |
D. | To perform various manipulations before indicating or recording results |
E. | None of the above |
Answer» C. Indication by numbers or some other symbol of discrete increments, the value of some quantity |
415. |
In a drilling machine having six spindle speeds if first five speeds are 458, 605, 800, 1055 and 1390 rpm, the next higher speed would be |
A. | 1760 rpm |
B. | 1500 rpm |
C. | 1830 rpm |
D. | 1630 rpm |
E. | 1440 rpm |
Answer» C. 1830 rpm |
416. |
A pattern maker's contraction rule accounts for |
A. | All materials of the pattern |
B. | All materials to be cast |
C. | Only shrinkage allowance |
D. | Only shrinkage, draft and distortion allowances |
E. | All pattern allowances |
Answer» C. Only shrinkage allowance |
417. |
The horizontal force required to slide the tail stock would be |
A. | 1000 kg |
B. | 648.84 kg |
C. | 100 kg |
D. | 148.84 kg |
E. | 500 kg |
Answer» D. 148.84 kg |
418. |
The audible spectrum of sound is in the range of |
A. | 0 to 100 cps |
B. | 30 to 15000 cps |
C. | 15000 to 25000 cps |
D. | 25000 to 10000 cps |
E. | None of the above |
Answer» B. 30 to 15000 cps |
419. |
Size of a shaper is generally specified by |
A. | Length, breadth and height of machine |
B. | Maximum travel of cutting tool |
C. | Weight of the machine |
D. | Quick return ratio |
E. | The area of machined surface per hour |
Answer» B. Maximum travel of cutting tool |
420. |
Which of the following process is preferred for the welding of grey cast iron? |
A. | Oxy-acetylene |
B. | Thermit |
C. | MIG |
D. | TIG |
E. | Submerged arc |
Answer» A. Oxy-acetylene |
421. |
For mild steel work piece using carbide tool, the temperature at which maximum materials is removed is |
A. | 200?C |
B. | 275?C |
C. | 100?C |
D. | Near zero deg centigrade |
E. | Below room temperature |
Answer» B. 275?C |
422. |
The surface speed of regulating wheel in case of centreless grinding is |
A. | 1500 - 1800 M/min |
B. | 15 - 75 M/min |
C. | 1000 - 1500 M/min |
D. | 100 - 500 M/min |
E. | 500 - 800 M/min |
Answer» B. 15 - 75 M/min |
423. |
Which of the following is considered to be non-machinable by conventional processes? |
A. | Grey cast iron |
B. | Silicon bronze |
C. | Parting off |
D. | While cast iron |
E. | Cast copper |
Answer» D. While cast iron |
424. |
The cemented carbide tools are generally poor in |
A. | Compression |
B. | Tension |
C. | Shear |
D. | Torsion |
E. | None of the above |
Answer» C. Shear |
425. |
Which quality of fit is provided for plummer block bearings? |
A. | H8f8 |
B. | H6f6 |
C. | H8d8 |
D. | H6g5 |
E. | None of the above |
Answer» C. H8d8 |
426. |
All of the following are metal cleaning methods EXCEPT |
A. | Parting off |
B. | Phosphatizing |
C. | Knurling |
D. | Abrasion blasting |
E. | Tumbling |
Answer» C. Knurling |
427. |
Which one of the following is a natural abrasive? |
A. | Alundum |
B. | Corundum |
C. | Boron carbide |
D. | Carborundum |
E. | None of the above |
Answer» B. Corundum |
428. |
In automatic control systems what could be the source of process disturbances? |
A. | Changes in supply |
B. | Changes in demand |
C. | Changes in environmental and other associated variables |
D. | Change in set point |
E. | Any of the above |
Answer» E. Any of the above |
429. |
The maximum peripheral speed of a grinding wheel is limited by |
A. | The work material |
B. | The diameter of the wheel |
C. | The frive limitations |
D. | The size of the work piece |
E. | The kind of bond used in the wheel |
Answer» E. The kind of bond used in the wheel |
430. |
Continuous chips |
A. | Are easily disposable |
B. | Sintering |
C. | Cause good surface finish |
D. | Waste power due to heat generation |
E. | Do not require cooling |
Answer» D. Waste power due to heat generation |
431. |
Fetling of castings is done to |
A. | Fill the void by welding |
B. | Smoothen surfaces |
C. | Remove the extra material from castings |
D. | To remove internal stresses from castings |
E. | To produce uniformly cooled castings. |
Answer» C. Remove the extra material from castings |
432. |
Lathe bed is made of |
A. | Mild steel |
B. | Close grain cast iron |
C. | Cast steel |
D. | Pig iron |
E. | Alloy steel |
Answer» B. Close grain cast iron |
433. |
In a shrink rule the graduations are |
A. | Slightly longer than the regular graduations |
B. | Same as regular graduations |
C. | Slightly shorter than the regular graduations |
E. | None of the above |
Answer» A. Slightly longer than the regular graduations |
434. |
The purpose of using a core in moulding is |
A. | To produce sound casting |
B. | To permit uniform flow of metal during moulding |
C. | To enable easy removal of pattern |
D. | To produce chilled surface |
E. | To provide desired recesses in casting |
Answer» E. To provide desired recesses in casting |
435. |
A micron is |
A. | 0.01 mm |
B. | 0.1 mm |
C. | 1 mm |
D. | 0.0001 mm |
E. | 0.001 mm |
Answer» E. 0.001 mm |
436. |
Investment casting uses pattern made of |
A. | Clay |
B. | Wood |
C. | Metal |
D. | Plastic |
E. | Wax |
Answer» E. Wax |
437. |
Metal patterns are used for |
A. | Large castings |
B. | Large scale production of castings |
C. | Complicated castings |
D. | Precision castings |
E. | Small castings |
Answer» B. Large scale production of castings |
438. |
In a lathe power feed is generally not available for |
A. | Lead screw |
B. | Carriage |
C. | Cross slide |
D. | Compound slide |
E. | All of the above |
Answer» D. Compound slide |
439. |
Bellows are |
A. | Used in foundry for cleaning the casting |
B. | Used in foundry for blowing loose sand from cavities and surface of the mould |
C. | Used in foundry for smoothening and cleaning out depression in the mould |
D. | Used in foundry for repairing the moulds |
E. | Used in foundry for moistening the mould |
Answer» B. Used in foundry for blowing loose sand from cavities and surface of the mould |
440. |
Which one of the following methods cannot be used for turning internal tapers? |
A. | Tail stock offset |
B. | Cross slide |
C. | Compound slide |
D. | All of the above |
E. | None of the above |
Answer» A. Tail stock offset |
441. |
Which of the following is not a chipless machining process? |
A. | Rolling |
B. | Grinding |
C. | Extruding |
D. | Die casting |
E. | Cold heading |
Answer» B. Grinding |
442. |
During planning the chips produced are in the form of |
A. | closed spirals |
B. | long helics |
C. | Parting off |
D. | spinters |
E. | fragments |
Answer» E. fragments |
443. |
Choose the incorrect statements. A coolant should be |
A. | Good lubricant |
B. | Generally not provided |
C. | Harmless to operator and machine |
D. | Transparent |
E. | Light in weight |
Answer» E. Light in weight |
444. |
Which of the following centre is used for holding hollow jobs on a lathe? |
A. | Oil groove centre |
B. | Revolving centre |
C. | Half centre |
D. | Square centre |
E. | Pipe centre |
Answer» E. Pipe centre |
445. |
Which of the following process needs high current for its operation? |
A. | Electro chemical machining |
B. | Ultrasonic machining |
C. | Abrasive machining |
D. | Electron beam machining |
E. | Electric discharge machining |
Answer» A. Electro chemical machining |
446. |
For short-distance transmission, the methods of transmission that can be used is |
A. | Hydraulic |
B. | Pneumatic |
C. | Electric and electronic |
D. | Any of the above |
E. | None of the above |
Answer» D. Any of the above |
447. |
In a cupola |
A. | Wind box and tap hole are at the same level |
B. | Slag spout is below tape hole |
C. | Slag spout is above wind box |
D. | Tape hole is below wind box |
E. | Tape hole is above wind box |
Answer» D. Tape hole is below wind box |
448. |
How wire anemometers are generally used to |
A. | Measure thermal conductivity of solids |
B. | Measure pressure of fluids |
C. | Measure temperature of moving fluid |
D. | Measure velocity of air steam |
E. | Measure magnetic properties |
Answer» D. Measure velocity of air steam |
449. |
In EDM, the erosion of metal occurs due to |
A. | Eddy current generated on the metal surface |
B. | Highly ionised electrolyte impinging on the metal surface |
C. | Chemical erosion |
D. | Rapidly recurring spark discharges impinging against the surface of work piece |
E. | Molecular transfer |
Answer» D. Rapidly recurring spark discharges impinging against the surface of work piece |
450. |
The tool used for punching small indentations/establishing points for divider is termed as |
A. | Solid punch |
B. | Parting off |
D. | Hollow punch |
E. | Prick punch |
Answer» E. Prick punch |
Done Studing? Take A Test.
Great job completing your study session! Now it's time to put your knowledge to the test. Challenge yourself, see how much you've learned, and identify areas for improvement. Don’t worry, this is all part of the journey to mastery. Ready for the next step? Take a quiz to solidify what you've just studied.