McqMate
1. |
What is the common angle of projection, for the Isometric view? |
A. | First Angle |
B. | Second Angle |
C. | Third Angle |
D. | None of above |
Answer» C. Third Angle |
2. |
Name the AutoCAD tool bar where you find the hidden Line Types? |
A. | Draw Toolbar |
B. | Modify Toolbar |
C. | Command Line |
D. | Object Properties Toolbar |
Answer» D. Object Properties Toolbar |
3. |
Name the Orthographic projections for the Isometric view “C” |
A. | Plan |
B. | Front |
C. | R.H End Elevation |
D. | L.H End Elevation |
Answer» A. Plan |
4. |
What type of drawing is it? |
A. | Isometric |
B. | Orthographic |
C. | Isobaric |
D. | None of above |
Answer» A. Isometric |
5. |
In which bar do you find the “Snap & Grid” icon? |
A. | Draw Toolbar |
B. | Modify Toolbar |
C. | Status bar |
D. | Object Properties Toolbar |
Answer» C. Status bar |
6. |
AutoCAD draw tool bar symbol is used for : |
A. | polygon |
B. | Rectangle |
C. | Pentagon |
D. | Construction line |
Answer» A. polygon |
7. |
What does this AutoCAD icon represent? |
A. | Arc |
B. | Spline |
C. | Polyline |
D. | Line |
Answer» C. Polyline |
8. |
Identify the following symbol, found in MODIFY TOOL BAR |
A. | Offset |
B. | Scale |
C. | Mirror |
D. | Cloud |
Answer» D. Cloud |
9. |
In Auto-CAD, a circle can be draw by the following commands: |
A. | Centre-Radius |
B. | Centre- Diameter |
C. | Two Points |
D. | All of above |
Answer» D. All of above |
10. |
In Auto-CAD object snap is used to pick accurately--------------of a line. |
A. | End point |
B. | Mid point |
C. | Nearest point |
D. | All of above |
Answer» D. All of above |
11. |
Name the Orthographic projection view “a”? |
A. | Plan |
B. | Front |
C. | R.H End Elevation |
D. | L.H End Elevation |
Answer» A. Plan |
12. |
What type of drawing is it ? |
A. | Isometric |
B. | Orthographic |
C. | Isobaric |
D. | None of above |
Answer» A. Isometric |
13. |
In the adjacent figure, the front width & height view dimensions are: |
A. | 80, 40 |
B. | 40, 20 |
C. | 80, 20 |
D. | 10, 20 |
Answer» A. 80, 40 |
14. |
In which bar do you find the “Ortho & Osnap” icon? |
A. | Draw toolbar |
B. | Modify toolbar |
C. | Object properties toolbar |
D. | Status bar |
Answer» D. Status bar |
15. |
AutoCAD “draw tool” bar symbol is used for ------------command. |
A. | Pentagon |
B. | Rectangle |
C. | Array |
D. | Construction line |
Answer» C. Array |
16. |
What does this AutoCAD icon represent? |
A. | Arc |
B. | Spline |
C. | Polyline |
D. | Rotate |
Answer» D. Rotate |
17. |
In AutoCAD, an arc can be drawn by the following command: |
A. | Start, End, Radius |
B. | Start, End, Direction |
C. | Three Points |
D. | All of the above |
Answer» D. All of the above |
18. |
In AutoCAD, “Ortho” command is used to draw--------------lines. |
A. | Perpendicular |
B. | Inclined |
C. | Polyline |
D. | All of above |
Answer» A. Perpendicular |
19. |
What does this AutoCAD symbol represent? |
A. | Inclined |
B. | Chamfer |
C. | Fillet |
D. | Radius |
Answer» B. Chamfer |
20. |
In AutoCAD, ------------- command is used to round the corners of a rectangle. |
A. | Break |
B. | Chamfer |
C. | Fillet |
D. | Extend |
Answer» C. Fillet |
21. |
In AutoCAD, the most common used coordinate systems are |
A. | Relative |
B. | Polar |
C. | Direct distance |
D. | All of above |
Answer» D. All of above |
22. |
Orthographic drawing refers to a 2D (two-dimensional) representation of an object in a view that shows only ----------- at a time. |
A. | One side |
B. | Two sides |
C. | Three sides |
D. | All sides |
Answer» A. One side |
23. |
In the third-angle projection; the top view of an isometric drawing is projected on --------plane. |
A. | Front |
B. | Side |
C. | Top |
D. | All of the above |
Answer» C. Top |
24. |
In AutoCAD, a poly line can be drawn by: |
A. | Draw toolbar |
B. | Modify toolbar |
C. | Command line |
D. | Object properties toolbar |
E. | All of the above |
Answer» A. Draw toolbar |
25. |
Name the Orthographic projection view “b” shown in the adjacent figure |
A. | Plan |
B. | Front |
C. | R.H End Elevation |
D. | L.H End Elevation |
Answer» B. Front |
26. |
In which Auto CAD tool bar do you find the “Grid & Snap” icon? |
A. | Draw toolbar |
B. | Modify toolbar |
C. | Status bar |
D. | Object properties toolbar |
E. | None of the above |
Answer» C. Status bar |
27. |
AutoCAD “Modify toolbar” symbol is used for ----------command. |
A. | Offset |
B. | Rectangle |
C. | Array |
D. | Move |
E. | None of the above |
Answer» D. Move |
28. |
The chamfer command is used to cut the corners of a-------------- at 45 degree. |
A. | Circle |
B. | Polygon |
C. | Rectangle |
D. | Ellipse |
E. | None of the above |
Answer» C. Rectangle |
29. |
What is the diameter of circle “B” |
A. | 20 |
B. | 28 |
C. | 30 |
D. | 40 |
E. | 50 |
Answer» B. 28 |
30. |
What is the arc radius of “A” |
A. | 20 |
B. | 21 |
C. | 22 |
D. | 23 |
E. | 40 |
Answer» A. 20 |
31. |
How many hidden circles from front view? |
A. | 1 |
B. | 2 |
C. | 3 |
D. | 4 |
E. | None of the above |
Answer» B. 2 |
32. |
An “arc” can be drawn by |
A. | Start, end, direction |
B. | Start, end, radius |
C. | Start, center, end |
D. | 3 points |
E. | All of the above |
Answer» E. All of the above |
33. |
In the AutoCAD a circle can be drawn by |
A. | Center, radius |
B. | Center, diameter |
C. | 3 points |
D. | All of the above |
Answer» D. All of the above |
34. |
Identify the following symbol, found in “modify tool bar |
A. | Trim |
B. | Extend |
C. | Chamfer |
D. | Break |
E. | Fillet |
Answer» B. Extend |
Done Reading?