McqMate
These multiple-choice questions (MCQs) are designed to enhance your knowledge and understanding in the following areas: Uncategorized topics .
| 201. |
The power tillage is most suitable for |
| A. | Stationary operation |
| B. | Deep ploughing |
| C. | Rotary operation |
| D. | All are correct |
| Answer» C. Rotary operation | |
| 202. |
Flooding nozzles have spray angle of |
| A. | 30-45 degree |
| B. | 60-90 degree |
| C. | 90-120 degree |
| D. | 100-150 degree |
| Answer» D. 100-150 degree | |
| 203. |
The teeth on the crankshaft gear is |
| A. | Half to camshaft gear |
| B. | Equal to camshaft gear |
| C. | Double of camshaft gear |
| D. | Four times camshaft gear |
| Answer» A. Half to camshaft gear | |
| 204. |
In a 30 days of retention period, the production of gas/kg of fresh dung is |
| A. | 0.04 m3 |
| B. | 0.05 m3 |
| C. | 0.06 m3 |
| D. | 0.08 m3 |
| Answer» C. 0.06 m3 | |
| 205. |
drag link is component of |
| A. | Clutch system |
| B. | Fuel supply system |
| C. | Transmission system |
| D. | Streering system |
| Answer» D. Streering system | |
| 206. |
The friction forces existing between the surfaces in relative motion is called |
| A. | Static friction |
| B. | Coefficient of friction |
| C. | Kinetic friction |
| D. | Angle of internal friction |
| Answer» C. Kinetic friction | |
| 207. |
Rietz mill is applicable for milling |
| A. | Dry material |
| B. | Semi-dry material |
| C. | Wet material |
| D. | All are correct |
| Answer» C. Wet material | |
| 208. |
Crushing law was proposed by |
| A. | Rittinger |
| B. | Kick |
| C. | Bond |
| D. | None of these |
| Answer» A. Rittinger | |
| 209. |
Ocean waves contain |
| A. | Kinetic energy |
| B. | Potential energy |
| C. | Static energy |
| D. | All are correct |
| Answer» D. All are correct | |
| 210. |
Biogas is a mixture of |
| A. | Methane and carbon dioxide |
| B. | Ethane and carbon dioxide |
| C. | Ethane and methane |
| D. | Ethane and carbon mono oxide |
| Answer» A. Methane and carbon dioxide | |
| 211. |
A pump used a power steering system is |
| A. | Gear pump |
| B. | Vane pump |
| C. | Both (a) & (b) |
| D. | None of these |
| Answer» C. Both (a) & (b) | |
| 212. |
The size of disc harrow is determined by |
| A. | Maximum width of cut |
| B. | Maximum depth of cut |
| C. | Number of disc |
| D. | Number of gangs |
| Answer» A. Maximum width of cut | |
| 213. |
Fluidized bed separator used to separate the seed is |
| A. | Lighter seeds |
| B. | Medium seeds |
| C. | Heavier seeds |
| D. | All kinds of seeds |
| Answer» A. Lighter seeds | |
| 214. |
Evaporation from water bodies and soil masses together with the transpiration from vegetation is termed as |
| A. | Evapotranspiration |
| B. | Water loss |
| C. | Total loss or total evaporation |
| D. | All are correct |
| Answer» D. All are correct | |
| 215. |
The capacity of kothar type storage structure varies from |
| A. | 5 to 15 tonnes |
| B. | 7 to 25 tonnes |
| C. | 9 to 35 tonnes |
| D. | 10 to 40 tonnes |
| Answer» C. 9 to 35 tonnes | |
| 216. |
The expected annual life of harrow is |
| A. | 8 years |
| B. | 10 years |
| C. | 12 years |
| D. | 14 years |
| Answer» B. 10 years | |
| 217. |
The ratio of the overall surface area of the ground product to overall surface area of the feed is called |
| A. | Grinding efficiency |
| B. | Coefficient of grinding |
| C. | Degree of grinding |
| D. | Milling efficiency |
| Answer» C. Degree of grinding | |
| 218. |
A potato planter is |
| A. | Automatic planter |
| B. | Semi-automatic planter |
| C. | Self-propelled planter |
| D. | All are correct |
| Answer» D. All are correct | |
| 219. |
The hoe type furrow openers work well in |
| A. | Trashy soils |
| B. | Sticky soils |
| C. | Root infested soil |
| D. | All are correct |
| Answer» C. Root infested soil | |
| 220. |
The particle size of clay according to USWA is |
| A. | 0.002 mm |
| B. | <0.002 mm |
| C. | 0.002 to 0.05 mm |
| D. | 0.5 to 1.0 mm |
| Answer» B. <0.002 mm | |
| 221. |
Pump used in inline system of injection is driven by |
| A. | Camshaft |
| B. | Crankshaft |
| C. | Belt-pulley |
| D. | None of these |
| Answer» A. Camshaft | |
| 222. |
The first IC engine was invented in the year |
| A. | 1876 |
| B. | 1890 |
| C. | 1900 |
| D. | 1905 |
| Answer» A. 1876 | |
| 223. |
In dry milling of pulses with seed oil treatment, oils is used at a rate of |
| A. | 0.5 to 1.5 kg/tonne |
| B. | 1.5 to 2.5 kg/tonne |
| C. | 2.5 to 3.5 kg/tonne |
| D. | 3.5 to 1.5 kg/tonne |
| Answer» B. 1.5 to 2.5 kg/tonne | |
| 224. |
Secondary winding consist of |
| A. | 10000-15000 turns |
| B. | 15000-2000 turns |
| C. | 15000-25000 turns |
| D. | None of these |
| Answer» B. 15000-2000 turns | |
| 225. |
The spacing between two adjacent discs in Olpad thresher is |
| A. | 5 cm |
| B. | 10 cm |
| C. | 15 cm |
| D. | 20 cm |
| Answer» C. 15 cm | |
| 226. |
Sun radiation temperature corresponding to black body temperature is at about |
| A. | 3000 K more |
| B. | 5000 K more |
| C. | 6000 K more |
| D. | 7000 K more |
| Answer» C. 6000 K more | |
| 227. |
In disc harrow the angle made by the axis of the arbor bolt with the direction of travel is |
| A. | Disc angle |
| B. | Tilt angle |
| C. | Gang angle |
| D. | None of these |
| Answer» C. Gang angle | |
| 228. |
The PTO HP of a tractor is |
| A. | Less than drawbar |
| B. | More than engine HP |
| C. | More than drawbar HP |
| D. | Less than friction HP |
| Answer» C. More than drawbar HP | |
| 229. |
Oil pump is driven by |
| A. | Oil pump is driven by: |
| B. | Timing gear |
| C. | Crankshaft |
| D. | All are correct |
| Answer» B. Timing gear | |
| 230. |
The mould board plough absorb side forces mainly through the |
| A. | Share |
| B. | Mould board |
| C. | Land disc |
| D. | Frog |
| Answer» C. Land disc | |
| 231. |
A splined shaft used for taking off power from engine is |
| A. | Final drive |
| B. | Drawbar |
| C. | Power takes off |
| D. | Differential |
| Answer» C. Power takes off | |
| 232. |
One bar is equal to |
| A. | 1 Kpa |
| B. | 5 Kpa |
| C. | 10 Kpa |
| D. | 100 Kpa |
| Answer» D. 100 Kpa | |
| 233. |
Parboiling of paddy is done to |
| A. | Achieve maximum recovery of head rice |
| B. | Minimise the broken percentage |
| C. | Reduce the milling losses |
| D. | All are correct |
| Answer» D. All are correct | |
| 234. |
Centrifugal governor is also termed as |
| A. | Maximum speed governor |
| B. | Minimum speed governor |
| C. | Both (a) & (b) |
| D. | None of these |
| Answer» A. Maximum speed governor | |
| 235. |
Which of the biogas plant has digester tank and gasholder as combined unit? |
| A. | Floating dome type |
| B. | Fixed dome type |
| C. | Both (a) & (b) |
| D. | None of these |
| Answer» B. Fixed dome type | |
| 236. |
The camshaft controls |
| A. | Valve closing |
| B. | Valve opening |
| C. | Valve timing |
| D. | All are correct |
| Answer» D. All are correct | |
| 237. |
The mechanical efficiency of spray pumps ranges from |
| A. | 50-60% |
| B. | 50-70% |
| C. | 50-80% |
| D. | 50-90 % |
| Answer» D. 50-90 % | |
| 238. |
Heavy smoking in an engine during operation may be due to |
| A. | Rich mixture |
| B. | Overloading |
| C. | Late injection |
| D. | All are correct |
| Answer» D. All are correct | |
| 239. |
Medium size bullock can develop |
| A. | 0.50 to 0.75 hp |
| B. | 0.75 to 1.0 hp |
| C. | 0.75 hp to 1.1 hp |
| D. | 1.0 to 1.5 hp |
| Answer» A. 0.50 to 0.75 hp | |
| 240. |
Tractor front mounted reaper is operated at a forward speed of |
| A. | 1.5 km/h |
| B. | 2.0 km/h |
| C. | 2.5 km/h |
| D. | 3.0 km/h |
| Answer» D. 3.0 km/h | |
| 241. |
The uneven furrow formation in disc ploughing is due to |
| A. | Disc angle is not uniform |
| B. | Loose bearing of disc |
| C. | Hitching defects of disc plough |
| D. | All are correct |
| Answer» D. All are correct | |
| 242. |
The increase in tilt angle of disc plough influences |
| A. | Penetration of disc |
| B. | Width of cut |
| C. | Reduce penetration of disc |
| D. | Reduce width of cut |
| Answer» A. Penetration of disc | |
| 243. |
The fan of radiator is driven by |
| A. | Camshaft |
| B. | Crankshaft |
| C. | Flywheel |
| D. | All are correct |
| Answer» A. Camshaft | |
| 244. |
Contour trenching is performed to |
| A. | Control the landslide from the hill face |
| B. | Conserve the moisture |
| C. | Both (a) & (b) |
| D. | None of these |
| Answer» B. Conserve the moisture | |
| 245. |
A thresher causes more seed damage if |
| A. | Speed is increased |
| B. | Clearance increased |
| C. | Speed is decreased |
| D. | Feed rate is reduced |
| Answer» A. Speed is increased | |
| 246. |
Hand dropper consists of |
| A. | A serrated blade |
| B. | A pair of serrated blade |
| C. | A plane blade |
| D. | A pair of plane blade |
| Answer» B. A pair of serrated blade | |
| 247. |
The shape of furrow cut by MB plough is |
| A. | V-shape |
| B. | L-shape |
| C. | W-shape |
| D. | M-shape |
| Answer» B. L-shape | |
| 248. |
Secondary fuel filter is used to remove the particles of size |
| A. | 1 Micron |
| B. | 2 Micron |
| C. | 3 Micron |
| D. | 4 Micron |
| Answer» B. 2 Micron | |
| 249. |
The gang angle of disc harrow is adjusted in the range of |
| A. | 0-30? |
| B. | 30-60? |
| C. | 60-90? |
| D. | Above 90? |
| Answer» A. 0-30? | |
| 250. |
Erosivity is the |
| A. | Climatic aggressiveness |
| B. | Soil aggressiveness |
| C. | Both (a) and (b) |
| D. | None of these |
| Answer» A. Climatic aggressiveness | |
Done Studing? Take A Test.
Great job completing your study session! Now it's time to put your knowledge to the test. Challenge yourself, see how much you've learned, and identify areas for improvement. Don’t worry, this is all part of the journey to mastery. Ready for the next step? Take a quiz to solidify what you've just studied.